AMIDON TECH DATA BOOK PDF

Amidon Tech Data Book datasheet, cross reference, circuit and application notes in pdf format. Amidon tech data book download, nutrition dietetics books free download, nutrition and dietetics books free download, veterinary acupuncture free download. Amidon’s technical data and, to a degree on our own experience. . book Low- Band DXing, meter guru John Devoldere states “A good transformer has an.

Author: Jushura Doutilar
Country: Guinea
Language: English (Spanish)
Genre: Sex
Published (Last): 2 October 2007
Pages: 339
PDF File Size: 14.58 Mb
ePub File Size: 6.20 Mb
ISBN: 843-1-66024-632-8
Downloads: 46746
Price: Free* [*Free Regsitration Required]
Uploader: Tasida

Amidon tech data book download

First you need to define your inductor parameters such as Q, inductance frequency of operation etc. A few t toroids are useful but the daga one can often etch used in its place. Something to be aware of: More dxta, is there a significant difference between a T and a T in an output filter? I would buy type 43 in the smaller ft37 size while the larger t50 is more widely used for type 2 and 6 materials.

Type 2 material is often used in output filters. For example, a 3rd order 0. I personally avoid powder iron or ferrite use in VCO tank circuits due to the temperature coefficient and gravitate to ceramic forms if possible.

How to choose toroids? Here is a summary: Also Micrometals has a chart which delineates their recommendations for which core material to use in a particular frequency range.

These 3 types cover many simple projects while something amidoh exotic may use even more material types. Avoid multilayer windings on toroids. Type 43 is a common ferrite for transformers. NU9J on April 20, If you will have DC circulating currents passing through the inductor then you need to run the numbers per the catalog guide for the effect on inductance.

It is not forbidden but generally will lower the Q substantially. Then you can go Micrometals site at www. I figured that out while adding a worksheet on toroids to my electronics calcs workbook. Type 6 is more often found in vfo coils. The resonant circuits and frequency range link will be of interest.

Powered by SMF 1.

Either would work in your case, though the red -2 core might be preferred. The end result of excessive temps is usually lower inductance and Q. The Handbook values are based on microHenries per turns for AsubL.

Amidon publishes a lot of material about amkdon cores, including the recommended frequency range over which each type will give optimum Gech. I also calculated 16 and 18 respectively rounding down. These curves also often present Q plots for the same number of turns with differing wire gauges. Thus unless the filter is intended to be lossy I would opt for the -6 material as it has the better temprature co-efficient and optimal Q.

And you may find slightly different ranges quoted in different places. KX4OM on August 24, Keep in mind you can see an appreciable rise in Q by using a larger gauge wire. Any reason to choose one over the other?

G3YNH info: Current transformers. Part 2.

That doesn’t mean that most cores can’t be used outside the stated range, and you may see -6 cores used on 40m transmitter projects. You can download Micrometals version H catalog on their RF products which contain many Q vs frequency graphs for differing parts at the following link http: Powder iron and ferrites both can be damaged by high temps causing failure of binding agents in the material.

Micrometals data indicates the -2 material is useful from KHz to 10 MHz and -6 material is rated from 3 to 40 MHz. If trch with a VCO the -6 material will probably be easier to compensate with temperature compensating caps than the And just to make the connection clear, Amidon sells cores from Micrometals or possibly similar materials from other sources.

Print Page – How to choose toroids?

Also his prices are much lower than that place mentioned. That difference in turns you dataa seems way too small to me as something msy be in error. Their plots focus on achieving maximum Q for discrete selected values of inductance. For example, fata -2 cores are recommended for 2 – 30 MHz, the -6 cores for 10 – 50 MHz, and the less common white -7 cores for 3 – 35 MHz providing a bit better temperature stability than the -6 types.