Find the most up-to-date version of JSA – JIS K at Engineering COM PDF – Search results, DOWNLOAD. JIS K STANDARD SDOCUMENTS2. COM jis k standard pdf Specimen. Sample Cutting Dies Ã ¢â‚¬â€œ. cert. no. ) 03/20/ page 1 of 14 scope of accreditation to iso , Jis K Free Download Here JIS K. physical testing methods .
|Published (Last):||28 October 2011|
|PDF File Size:||20.12 Mb|
|ePub File Size:||19.54 Mb|
|Price:||Free* [*Free Regsitration Required]|
The Pressure foot in contact with the specimen is 44mm in width and 18mm in depth, wide enough to ensure accurate measurement.
Dispersion of polystyrene jis k 6301 standard can be judged. As is half ball type osibari this is suitable for soft material like soft rubber expanded rubberhardness of spool of textile and film roll to which osibari sticks if it is type A durometer. This is basically equal to JIS K of durometeras only its round jis k 6301 standard method of spring load figure etc. Constant Loader for Durometer Constant loarder assures uniform test pressure eliminating false readings due to differences between operators in measuring by hand.
However, verification is recommended because a significant difference is estimated to syandard the largest when a durometer indicates measurement values from 10 to 90 points.
Our product line consists of various types of durometers applicable to specific materials as indicated in the chart above.
However, it jis k 6301 standard used for 50 years as rubber hardness measurement and is still used as test data jis k 6301 standard between concerned persons even now when it is progressed to shift to new JIS and the standard is discontinued. Type Shandard is suitable for hard rubber of which measured figure by Type A 90 and above and Type E is suitable for soft rubber of which measured figure is below Measurement example Hardness is being measured by placing GS G on the sponge sheet.
Type A which is main type tends to indicate higher figure by 1 or 2 points compared with conventional A hardness measurement. Then, long leg type complies with DIN JIS K which had been established in and sustaining the base of rubber industry in Japan was discontinued in after the 631 period, as it was not in conformity with ISO, and JIS K was newly established.
GS 4kg weight option ZY The stationary set hand max-hand makes the maximum value easier to read and allows the creep characteristics of a specimen.
But we distinguish jis k 6301 standard code as another durometer from conformity of standard point of view. Two-pointer type max-hand and active hand of Rubber Hardness Tester The stationary set hand max-hand makes the maximum value easier to read and allows the creep characteristics of a specimen.
jis k standard sdocuments2 com
High accuracy and repeatability of the hardness readings are assured by the flexible joint function. In case there unevenness on the measured face, less flat face because of irregular shape and deep bump at the stqndard, depressed face of jis k 6301 standard is difficult to reach and sometimes accurate measurement is not possible.
Inspection is conducted at 2, 50, and points respectively. It consists of 3 types of durometer such as Type A for medium stiffness, Type D for high hardness and Type D for low hardness.
Hardness Tester Selection Chart Our product line consists of various types of jis k 6301 standard applicable to specific materials as indicated in the chart above.
However, it is used even now for measurement data or internal management data upon the agreement of concerned parties jis k 6301 standard to its extensive use historically within the rubber industry.
Pressure foot The Pressure foot in contact with the specimen is 44mm in width and 18mm in depth, wide enough jis k 6301 standard ensure accurate measurement. Indentor Extension Tester The gauge to check the indentor height on a durometer and the reading indicator mechanism.
Night line and highest and lowest limiter equipped for the both are standard.
JIS K-6301 2
Type E 2 durometer with around half of sponge spring load figure of type E, and type FO to measure hardness of polystyrene sponge for the level of sponge washing dishes are available.
Stndard most important consideration in using durometers is to select the correct type for purposes of measurement according to the specimen. At that time, deep hole H and long leg type L make measurement possible by making pressed face small or jis k 6301 standard. To top of product jis k 6301 standard. tsandard
Please select according to usage in addition to type A and Type D. Load Tester for Hardness Tester Tester to check load properties of the spring on a durometer Inspection jis k 6301 standard conducted at 25, 50, and 75 points respectively. This standard is ruled by plastic business field in Japan apart from testing method of hardness of rubber.
There are 2 kinds stanvard A type for general rubber and C type for hard rubber.